OPA4354AIPWR OverviewPackaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. An op amp ic of the Voltage Feedback type. The op amp is delivered to you in a Cut Tape (CT) case. There is a growing number of terminations approaching the number of 14. The pins on this board total to 14 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A total of 14 pins are present on the instrumentation amplifier. There is an input offset voltage of 8mV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . As long as the supply current of the chip does not exceed 4.9mA, this op amp ic can operate. Keeping the voltage gain at 110dB is the best course of action. As far as the device is concerned, buffer amplifier has 4 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. For packing the buffer amplifier, the TR-axis is adopted.
OPA4354AIPWR Features14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA4354AIPWR ApplicationsThere are a lot of Texas Instruments
OPA4354AIPWR Instrumentational OP Amps applications.
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Weight | 140.30179mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OPA4354 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Channels | 4 |
| Operating Supply Current | 4.9mA |
| Supply Current-Max | 6mA |
| Slew Rate | 150V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 100MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 73.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 8mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Input Voltage Noise Density | 6.5nV/sqrt Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
+8613715157867