TL072IDT OverviewPackaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A J-FET-type buffer amplifier is shown here. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using a supply current of 1.4mA , this buffer op amp will be able to operate. Keeping the voltage gain at 106.02dB is the best course of action. 2 channels are available on the instrumentation amplifier. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
TL072IDT Features8 Pins
supply voltage of 15V
106.02dB voltage gain
TL072IDT ApplicationsThere are a lot of STMicroelectronics
TL072IDT Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | NICKEL/PALLADIUM/GOLD (NI/PD/AU) |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL072 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Output Current | 40mA |
| Min Input Voltage | -12V |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20pA |
| Max Input Voltage | 15V |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Max Frequency | 100kHz |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.004μA |
| Height | 1.25mm |
| Length | 5mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL072IDT Datasheet
+8613715157867